NR600

For the price this is hands down one of the best cases on the market! Check out GamerNexus review on the case. It’s extremely easy to build in, is good quality, looks amazing, has room for 360mm AIOs, 166mm Air Coolers, and any size GPU you like. The front is very easy to remove and is covered in fine mesh! This means it acts as a dust filter but also lets huge amounts of fresh air into the case! The cable management on this case is amazing. It has room for 5 SSDs and 1 HDD NOT counting the removable HDD tray located on the bottom on the back side of the case. The SSD/HDD mounting system is completely tool-less and fantastic. The top has duel USB 3.0 ports, an audio/mic port, and a power and reset switch. I can’t stress how amazing this case is for the price! The huge glass side panel looks so good, and it still has the bottom unit in it that covers up the PSU and all your wiring. I put 3 Cooler Master Sickleflow 120mm blue LED fans in the front as intakes, two 140mm Cooler Master Masterfan Pro RGB Air Pressure fans on the top as exhausts, and another 120mm Cooler Master Sickleflow Blue LED fan in the rear as exhaust. That’s 4 120mm fans and two 140mm fans total and it’s near 100% silent. The best part about the case imo is the amazing airflow. The 3 front fans push in so much cool ambient air it’s insane. There are no obstacles in the way to block the air either. The top fan pushes cool air straight to your CPU, the middle to your GPU, and the bottom to your SSDs and PSU. The top two fans and rear exhaust it all out of the case. It has the best airflow of any case I have ever built in and I previously had the Cooler Master HAF 912 and HAF X both of which were some of the most renowned cases for amazing airflow. In GamerNexus review of this case it shows just how amazing the airflow is with ONLY 3 fans. Just think if you have 4 120s and two 140mm fans in the case like I do! My components stay super frosty now. The case is cheap, good quality, easy to build in, has amazing airflow, holds full size coolers, cards, and anything you want, and has a glass side panel to top it all off. Once again this thing has room to hold FIVE SSDs and ONE HDD even without the HDD/SSD tray! That is crazy! It holds 3 ssds in the front for display through the glass and two more on the rear plus the HDD. If for some reason you need more than 5 SSDs and 1 HDD then you can fit a further 3 more( I think could be even more) in the tray. If you want a nice case that has amazing airflow, will support any AIO/CPU cooler and GPU you want, has tons of storage room, great cable management, a mesh front panel, AND a glass side panel then just press buy already. Check out the pictures I added. For 69.99 which is what I paid I have zero complaints. Edit - Added two new photos at the end after I got matching SSDs, matching NVMe drives, custom cable extensions, and re-did the cable management. Absolutely love this case. Looks fantastic, super spacious and easy to work in with amazing top of the line airflow!

The Masterbox NR600 is an outstanding airflow pc case. At just $70, it has better airflow than most $100 cases. It's an overall great case, but it does have some minor inconveniences to be considered. The dust filter underneath the PSU mount is flimsy and definitely cheap, but that's to be expected at the $70 price range. While it does support two 140mm case fans in the front, you will be better off with three 120mm. Also, while it does fit ATX builds just fine, it still doesn't leave much room at the top for more case fans. They can fit, but there's not a lot of breathing room. Finally, many people may consider this a drawback, but I don't personally care, It has a very simplistic look and doesn't have any RGB. Now, onto the good stuff. First and foremost, it is fantastic at moving air through the case. The front mesh does a good job keeping larger dust particles from getting into the system, which is uncommon for cheaper cases like this. The PCI slot tabs are removable without having to break them open permanently. Despite the PSU dust filter at the bottom being cheap, the dust filter at the top is magnetized and works pretty well. The hard drive cages behind the PSU mount are easily removable for better cable management, especially if you have a non-modular PSU. The stock fans actually work fairly well and are fairly quiet, too, but I would still recommend investing in some better fans. The tempered glass panel, back panel, and front mesh are all easily removable, and cable management in this case isn't that bad. In conclusion, if you're looking for a good sub-$100 gaming PC case, I would recommend this one even over the NZXT H500. The best thing you should do with this case is add 1 120mm case fan to the upper-front slot and get a decent third party cpu air cooler, like the Hyper 212. In my system, I'm running a Ryzen 5 3600 OC to 4.2 GHz, RTX 3060 ti, a MSI B550 Gaming Plus Motherboard, with the Hyper212 Black Edition, and a cheap case fan in the front slot. The air cooling is fantastic. It almost never goes above 71 C under full load. The highest I've ever seen the CPU is only 73 C, and that was while playing Battlefield V at 1440p medium to high settings with full RTX enabled. That 73 C was only at peak, it tends to hover around 67-69 C with those settings. Again, it's a fantastic case for air cooling and it's incredibly cheap, yet with outstanding performance.

- This specific cooler master case is simply amazing. Air intake and out capabilities are great. However I really do with it has 3 pre-installed fans rather than 2, it only has 2 intake fans pre-installs and no out-fans. The PSU hole was a little hard to work with the specific Power Supply that I have, the case has this little rubber stands on the PSU hole that were not helping at all, I think if the PSU I installed was modular, it would've been fine, but I had to remove those. As for cable management, oh my lord this case made it AMAZING to work with, lots of holes everywhere to pass the cables trough to connect, and rubber in between the holes to hide the cables. I loved working with this case. And for those wondering, it brought all the Standard ATX motherboard standoffs pre-installed, so that way nice. Be careful if you are not using a standard ATX motherboard..

Ottimo, buona fattura, arrivato con vetro intero (mano male ) e non danneggiato. Ottima la conformazione degli slot, dei supporti, della configurazione per la ventole (ne ho montate 3 in ingresso, una di estrazione e 2 di estrazione su dissipatore ad acqua perla CPU. cestello 3 HDD da 3,5 pollici + uno verticale ed altri x backu da da 2,5 pollici . Lo spazio è giusto giusto ma i cavi sul retro della MB aiutano molto. Attenzione spazio molto esiguo lato connettore aggiuntivo alimentazione MABO, se mettete un dissipatore ci sta tutto al pelo.

Este gabinete me ha impresionado bastante. Es espacioso sin ser gigantesco, el material se siente de calidad y el panel lateral es de vidrio templado. Permite un muy buen flujo de aire, lo cual se traduce a un muy buen rendimiento térmico.* Algunos podrían decir que solo es una "caja negra," pero a mi me gusta mucho como se ve esta "caja negra" en mi escritorio :) *Como referencia, tengo 3 ventiladores frontales (intake), un AIO de 240 montado arriba (exhaust) y el ventilador de 120mm que viene con la carcasa en la parte de atrás. Mi GPU nunca pasa de como 60C bajo carga y 36C idle (GTX 1070, ya sé viejito) y el CPU como 75C bajo carga y alrededor de 45C idle (Ryzen 5 5600X).

Great value for money

It has a few design "flaws", such as the non-movable HDD cage, but over all I would high recommend this case, especially for the price when on sale. You should install at least one more 120mm fan in the top front, but it has great air flow (esp w 1+ more fans), is not huge, and has room for 4 HDDs and several SSDs (5?), so it's a good option for gaming pc. I'm not sure how good it would be for water cooling though. The front really shouldn't have 140mm fans installed (so no 280), and I think a 360 AIO cooler may have a problem in the bottom section. A 240 cooler would probably be fine in the front.

Alguien sabe si puedo conseguir la malla de la parte de arriba del gabinete en algún lado ?. No traía el que compré. Y no lo quiero regresar puesto que acabo de armar todo y después me di cuenta. Actualización: la malla viene en la parte interior de la tapadera trasera, la que no tiene cristal.