TRUGLOairsoft-Gun-Sights

Perfect fit on a Stoeger pump gun with 6mm rib. A tad snug but some light encouragement with a rubber mallet seated them perfectly to the point I would venture to guess they would stay in place without the set screws. I agree with others who stated the fibers seem a bit small but that's not necessarily a con IMO. I replaced the front red fiber with a green one to match the rear (these old eyes have trouble with red) and now have a clear and bright full sight picture. The green gathers and projects a much sharper and clearly defined dot. Set screws are somewhat small and I could easily see getting too heavy with torquing them down and stripping or breaking them. I put just a touch of blue loctite on them, snugged them up and then gave them an additional light bump. Threadlocker will somewhat lube them allowing ease of installation versus dry threads so don't get too heavy handed with the included hex key. I don't foresee any issue's and these should do fine for turkey season.

This is the third set I have bought. All three were installed on 870 model shotguns including an 870 Supermagnum 12 gauge, and 870 Magnum 20 gauge and an 870 20 gauge Compact model. I have had zero fitting issues. On my 870 Magnum 20 it required a pretty big windage adjustment to get it centered but it did get centered. All three guns were built for turkey hunting and all three have stopped them in there tracks. Keep in mind... If you're going from a bead sight to these naturally your shot will drop. Be prepared to do some work with your shotgun if your patterns are fairly tight out to 40 yards. The fiber optics capture a lot of light and work fairly well in low light situations. I have had a few fibers break, but they come replacements which are easy to install. You cannot go wrong with this sight. Proofs in the pudding!

Very easy to install and a huge addition, thanks.

Not sure why other reviews are so low... Installed on a FedArm SS12, break action, single shot12ga, smooth barrel. 1) Yes it is a bit "fiddly" to install and the screws are itty bitty. Some patience and just a small bit of skill are needed. I found the correct post, screwed the top end into the sight and screwed the post into the tapped hole on my barrel. It didn't line up. It was almost 90 degrees off. No worries, loosen the post in the barrel and retighten. This advanced the sight more forward and after a few repetitions it was on tight and aligned straight. Read several reviews that said the fiber optic cracked on install. Obviously, finesse wins out over brute strength. Part of the post protruded into the barrel. Got out the Dremel and used a small, rough grit sanding drum. At 15,000 rpm it took just a quick touch to sand the post flush with the inside of the barrel. On hindsight the Dremel was probably overkill and a manual sanding would probably do you fine. 2) Height. Yep, this things sticks up a bit taller than a standard bead. Or at least on my application it did. Note in the closeup pic that there is a small gap between the sight and the barrel. Honestly this looks made for ribbed barrels so it would likely snug down way better there. Also, I didn't use any thread locker on it. Seems I got it tight enough the way I installed it. Fired several rounds and it didn't budge. YMMV 3) Asthetics. It ain't classic, but that's not what you look for in a product if this nature. I do like the look a lot though. Better than a snap on sleeve for a plain barrel or a magnetic mount for ribbed, either of which have a huge "look at me" aspect. This is discreet, yet functional. 4) Sight picture. It was all I could ask for. The SS12 has a rather deep sighting groove on the receiver and the TruGlo Fat Bead lined up nice with it. The Dual Color is a very nice touch and I can see myself liking this more and more as I go along. Overall I'm very satisfied. I took one star off because it is a slight pain to install and the mount isn't flush on my smooth barrel. It's not quite truly "universal." However, I think it's a quality product that does what it should and at a very attractive price.

Looks extremely nice and very well made,but did not fit my gun as advertised, (CZ 612 Magnum waterfowl). The provided shim added too much thickness to get the sights on the rib. Without it they would not really secure fully. Mine is an 870 clone but it seems to be non-standard in some dimensions except for the inner action mechanism. If you were getting this for a regular Remington 870 I have no doubt it would fit just fine. Each situation is unique of course. If one wanted to in my situation, they could use a thinner piece of plastic and make their own shim, it would be a simple fix but I gave up and decided to mount a red dot instead. But it's a really nice quality set of irons with a really fine aiming point. I'd say it's a good value for how well made it is, that's Truglo for you. Never been disappointed with one of their products.

It says its for airsoft so maybe thats why I attached it to my shotgun took it to a range and after firing my gun 1 time it snapped in 2 pieces

Fits Stoeger M3500 26" barrel well. **Update 9-Feb-2016** After two seasons of duck hunting in the swamp, and probably 300+ target rounds, the bead is holding up like a champ. My hunting buddies all like the look of the bead too. Some say it's puny in size, but I think it's great. Some reviews complain that the bead doesn't sit straight or it falls off. Please note that the mounting screws are threaded on both ends. If you can't get it to sit straight, it isn't the bead's fault. Blue threadlocker ensures that the bead won't fall off. Original review↓ After trying several different beads, I settled on this one. This one is the universal mount so it should fit about anything. I used a dab of blue thread-locker on both the bead base AND the gun itself. I would recommend this for anyone purchasing this product. I've lost beads before and there is nothing more annoying than lining up a shot and finding that your bead has gone AWOL. Pros:Large diameter bead speeds target acquisition, screws in flush with vent rib so you don't have the annoying "shelf" optical effect that most aftermarket beads have where the bead base is 0.5 mm higher than the surrounding rib. This was incredibly annoying to me on other products, and it really sold me on this bead. Universal mounting screws are threaded on both ends. This allows you thread a screw into the sight from the bottom, and then attach that screw to the gun. If the bead is slightly out of alignment to one side, simply back out the screw slightly from the bead base so more threads are available to be screwed into the gun. Cons:In my opinion, this dual color design is not as efficient as gathering light as a normal single color green bead, so it is not as bright. However, the dual color makes the sight visible against a variety of different backgrounds. This is incredibly helpful as you swing your barrel across tree cover and into clear sky like in a duck hunting situation.

The Windadge adjustment screw is difficult to tighten. Mine came already stripped out. Once you get it where you want it I recommend using JB quick weld to hold it in place. I contacted the company and let them know of my issue. They do not have extra screws for you to buy and only offered a 10% discount on a future purchase.

Good quality

This product is great! Very solid steel construction fits perfectly on my Winchester sxp hybrid hunter the sight picture is perfect!

best sight ever bought, i highly recommend the red one. fast shipping and high quality sight, eazy to install..... 5 stars

Seems fine.. after installing it I think it would be better if I had gotten the solid color. Other wise fine

よき