COOLWUFAN 3 Pack Outlet Wall Mount Holder for eero Pro 6 and Pro 6E

I bought this COOLWUFAN Wall Mount Holder to tidy up my eero Pro 6 setup, and it makes a huge difference. If you're looking to declutter your counters, this is the way to go. What I liked: Cable Management: The built-in cord groove is the best part. It winds up the excess power cable perfectly so you can finally say goodbye to messy wires hanging down the wall. Sturdy Fit: The eero units snap into the bracket securely. I don't have to worry about them vibrating loose or falling out of the outlet. Space Saving: By mounting these directly to the outlet, I cleared up valuable space on my side tables and desks. Simple & Clean: The white plastic matches the eero units perfectly, making the whole setup look like a professional, integrated part of the house. One minor thing: Outlet Orientation: Keep in mind that these are designed for vertical outlets. If your outlets are horizontal, the eero will sit sideways, which might look a little bit off depending on your preference. Overall, it's a simple, effective, and affordable upgrade for a much cleaner home network setup!

So far, the product performs as expected. No defects or issues noticed.

Long story short, the price is reasonable for a multi pack if you have multiple Eero Pro units. Product is simple and essentially just a plastic case the unit sits in with power cable wraps around the back of the unit for a seamless install. No fitment issues, only took a few minutes to install all of my units. I didn’t really think about clearance when I bought these, one of my ideal locations the outlet was only a few inches above the counter. I just cleared it with like .25” room under the unit. If you have ~9” from the countertop / table top to the top of the desired plug you’ll have no issues fitting it there. I could have plugged it into the top outlet, but then the bottom outlet would be covered. You can’t really install it upside down either as the plug is the only thing that holds the unit to the wall, so when you try to put it in the top plug upside down it’s too too heavy and will fall out. Similarly, I also installed one of these in my garage. I have outlets on the ceiling which would have been a more ideal spot for coverage, but the unit just pressure fits into the outlet and it would be too heavy and fall out / down. One potential enhancement they could make would be to provide double sided tape to hold the unit to the ceiling or upside down to allow for more install options than just hanging for the outlet. But for the price I’m happy, and I could probably just buy double sided tape and do it myself if i really wanted to but not worth the extra hassle.

I like these module holders. Once you get the hang of wrapping the cord thru the grooves, it is a very functional product. I'm going to buy more.

This wall mount does exactly what it’s supposed to: it holds the eero securely, keeps it off the counter, and makes the setup look much cleaner. Install was quick and straightforward, and everything feels stable once it’s in place. It’s a nice little upgrade if you want better organization and a more “built-in” look for your Wi-Fi gear. Great value for the price.

If you have an eero Pro 6E, make sure you get the updated holder with the indentations in each corner for the eero feet. There is an older review photo that shows no indentations (which makes the Pro 6E stick out and then the side holding tabs do not engage). With the updated holder, the side tabs fit flush, so the eero stays in place. The bottom half of the holder has the "lip" that holds the eero whereas the upper half does not, so the mm gap is normal. I like the design with the minimal plastic - better for heat dissipation and wifi signal.

perfect for the Eero 6 Pro. I have 2 of these one in the kitchen and one in the garage where it can get in the negatives during winter and over 100 during the summer.

According to the Specs, the newer Eero Pro 6E (Tri-band)) is the same width, but 1/10 of an inch thicker than the Eero Pro 6 (Dual-band). I purchased this for the Eero Pro 6. It fits great, but I don't think it will be able to hold a device that is only 1/10 of on inch thicker. If you are looking to purchase this for the Pro 6E, you might want to find a similar version specifically designed for that model.

I purchased these for the Eero Pro E6's I have at home. I didn't want them sitting on top of furniture and also had one I was looking at keeping in the upstairs hallway with no furniture nearby. These work well; my units are now hanging by the wall plug. I also like the fact that the back of these wall mount holders have a guide to store the extra cord so there are no visible wires on the floor. The one drawback is that no matter what i did, I couldn't seem to get my Eero units to sit completely flush to the mount. Its not a big issue, but would have been nice considering these mounts are intended to be designed for the Eero unit.

it works fine. The unit "hangs" from the electrical outlet, where the transformer plug is inserted into the electrical outlet. If your electrical outlet doesn't hold the plug well (aka "loose"), then a little velcro behind the plug can solve this issue.

Doesnt fit pro 6e.