283in PVC Wire Covers for Cords on Wall, One-Cord Cable Concealer Kit, Paintable Cable Raceway Management, Cord Hider, Max for 2 Small Cords for Home Office, W0.59in H0.4in

This cord concealer kit was exactly what I needed to clean up the mess of wires behind my wall-mounted TV. The channels are sturdy, spacious, and well-designed, easily fitting multiple cables like HDMI, power cords, and speaker wires. Installation was simple—just peel and stick with the included adhesive (or screw in if you prefer). The covers snap on securely but are easy to remove if you need to make changes later. I also love that the PVC material can be painted, so it blends perfectly with my wall color. The 125-inch length across 8 pieces gave me plenty of coverage, and the included connectors and corner pieces made it easy to work around edges and angles. If you're looking for a neat, professional-looking solution for hiding cords in your home or office, this kit is a great value. Highly recommended!

Wow! This worked Fantastic, and did what it said it does! Great product. Easy to use, & held all the wires I wanted in one unit (tight fit) instead of running two rows. I had 2 sets 18g red/blk jacketed plus 2 skinny sets jacketed red/blk speaker wires. You should ***pay Attention*** putting the correct part to the wall. One side (cover) has slight rounded edge & the backside has a straight flat edge. I didn't pay attn & some weren't lining up as smooth because I had put coverside to wall. No one would probably notice but it bugged me knowing it was wrong, lol, so I pulled off those pieces to redo. Which brings me to the double sided tape included, which is great & 'Strong - I didn't want hassle of using screws. ***Note IF you need to remove because of error, use a hairdryer on the plastic to warm up tape underneath to be able to pull off the wall, otherwise you might take part of wall.*** Thankfully I saw someone else mention this trick and worked like a charm! This does of course destroy the piece, but i had plenty extra & glad came with w/ 2 rolls of tape.

I love it and it does what it says. I gave it 4 stars only because it did not have enough of the straight connectors and you cannot buy just the straight connectors. To get them you have to buy a whole set. Aside from that it works well, does what it says and it is easy to use and install. It made my tangle of cables look neat and my wall and floor finished. I can recommend this product

Overall, I'd recommend this kit as it is well made, does the job and can cover a lot of space. I could see, however, that the installation might be tedious for someone not accustomed to figuring things out and the directions are no help. For example, it's not clear which side is the base and which is the cover (the cover fits OVER the base as shown on the outside of the box). Also, each of the covers must be cut shorter than the base as they fit partially into the joint covers, so you'll have to cut each cover even if you're using full runs of the base. Be careful not to abut the bases too close to woodwork or inside corners or you may not be able to snap the cover over the base. Once it's all done, it looks neat and tidy. I'd definitely buy it again, but I have a lot left over from my first install, so that's pretty good value.

These really had chords well. And easy to install.

I gave this product a try mainly because the product I usually get was going to arrive too late. I made sure in advance that the single cable I was using this application was small enough to fit based on the dimensions provided in the product description. When receiving the product, I again tested that it would fit, and that the covers snapped into place. However, when putting these in place, I noticed that those covers and the connectors provided don’t really snap together in a strong enough way that if there is a little tension from the cable, they hold. Other products are much stronger. I also don’t like how the connectors are engineered. They use a tab to stay down, rather than a snap in place method. I don’t recommend these except maybe for lightweight speaker wire that doesn’t need to be significantly held in place.

Good quality. We really like it.

These were super simple to set up, I ran them across my house from the living room to my bedroom to keep everyone from fumbling over cords and looking hideous. They keep the cords in place, I wouldn't suggest it if you are trying to keep kids out though, as the front pops off fairly easily and they get into it anyway, but aesthetically it serves its purpose, which is mostly what i needed them for.

Decent product that looks good, however it has 18 lengths and only 14 straight connectors. That means that unless you use three “elbow” connectors you are going to run out of connectors. To make matters worse, I had to cut a few lengths in half which means I am missing even more of the connectors needed to use the full kit.

I recommend the product.

I like the design of this better than some other cable covers which are relatively huge by comparison (and usually end up mostly empty), this is a lot more stealthy. It can fit a 14 gauge dual conductor wire with a large in-wall rated jacket but that's about it - still it's a lot thicker cable than I expected would fit through one channel. It comes with everything you need including connectors both straght and angled, and even tape to adhere the channels with. The channels are two parts, the part that goes against the wall and then a top cover for it - it's possible to snap the top cover over the bottom part but it's difficult and much easier to slide it from the side, but this is not very practical. Still, it's a lot better than having to try to fish cords all the way through a closed channel. The only thing I don't like about the kit is the connectors to join multiple pieces together, they're easy to use relatively and the channels just sort of slide into them, but each channel is short so you have these ugly bumps at pretty regular intervals along the run which I'm not a fan of. The other thing is that it's nice it comes with adhesive tape right in the box to use it, but I know from experience using this type of tape that it will absolutely destroy any paint you use it on so use it sparingly and wisely you are not going to want to have to reposition it after you put it on because it will take the paint off with it.

It’s not meant for hiding a huge mass of cables so it’s not as useful in some setups. If you just need to hide one length of cable, it’s perfect! Other than some planning and measuring, installation is straightforward and simple. Apply the adhesive tape to the back of the cable raceways, section by section, and apply where you want it. Insert the cable right away or snap/slide the covers in place as you work. A different cable concealing kit I have included the option to screw mount the cable raceways instead of relying on adhesive tap, but that's not an option here. In this cable concealing kit you get 304 inches of cable concealment. This includes: 18 x cable raceways (16.9 inches in length each = 304.2 inches) 14 x couplings/connectors 6 x flat elbow connectors (for making a 90° turn/angle along a wall) 2 x inside connectors (for connecting raceways in the corner of a room) 2 x outside connectors (for connecting cable raceways over a corner edge) 2 x rolls of adhesive tape

This is a comprehensive kit for concealing a single cable for almost any setup, with a total run length of just over 25’. The channels are very small – a 14AWG surge protector cable fills 100% of the channel. I’d hoped to use this upstairs since I only have a single (power) cord from the wall to TV, however the flat-style cord is too large for this channel (technically it fits, but twists the channel - see a photo attached). The channels easily fit a single 16AWG power or DisplayPort or HDMI cable, and could be used for a couple of speaker wires. The front covers snap on firmly. The couplings (which connect the 16.9” segments) fit over the segments, and will hide any imperfections caused if you’ve had to cut them down to size. Included are two rolls of double-sided tape. So far, I’ve only installed a single segment to hide a single HDMI cord running from my console to my TV (the other cords are run through a larger concealer channel). This size of concealer is ideal for a single standard-sized cable while maintaining as low of a profile as possible. If you have a larger single wire, you may wish to buy a larger channel kit. Overall, I’m really impressed with the build quality of this kit and how it looks when installed.