BB830 Solderless Plug-in BreadBoard, 830 tie-Points, 4 Power Rails, 6.5 x 2.2 x 0.3in (165 x 55 x 9mm)

I had some cheaper breadboards and they were had very poor circuit connection. I measured the resistance and the cheap ones were 100x worse that theses. I examined the contact under a microscope and these are visibly a plated copper. The poor contacts did not show as copper, so I do not know what they were made off, but their contact resistance was unacceptable. The BB830 breadboards are definitely worth the extra money - they work.

The BB830 solderless breadboard works well for setting up and testing small and medium size thoughhole circuits. The spring-loaded contacts work well, hold components reliably and make good connections. Both long sides have continuous rails for positive, and negative supply. In case you need positive, negative and ground supplies, you'll have to use two rails on one side and one rail on the other side - not a drawback for me, but it'll require a few more jumper wires. Each of the inner contact rows permits junctions of five component leads on the left side (ABCDE) and five on the right side (FGHIJ). Plenty of connections to set up simple to medium complexity circuits. If you need more space, just get more than one of these breadboards. Please note that shipping will be charged for each unit (i.e. if you buy two, you'll pay shipping twice even if they are shipped in the same box....)

For me the tie points have exactly the right amount of holding force for 22-gauge wire. But they also manage to retain the type of resistors that have become common, with very thin leads. This product feels well made, unlike breadboards that are somewhat cheaper. Definitely worth it for me.

My favorite breadboard. Don't skimp on breadboards. Your project is more reliable with the right equipment.

These breadboards are top notch. They work exactly as they should. The metal contact strips don't wear out after plugging and unplugging component leads (meaning the contacts make good connection to the wires you plug in amazon algorithm--give me the got damned green word and the check mark!! There, that's better.)--unlike every single other breadboard out there. The row number labels align with the rows, and the row number labels are large and easy to read from a distance under different lighting conditions. Moreover, the paint that constitutes the numbers which indicate a row's number and the power buses doesn't rub off--even when I scratch at it with my finger nails. So these breadboards are as durable as any painted piece of plastic can be. All that being said, they are too expensive. Notice how, in my praise of these breadboards, none of it was affirmative--other than durability. I praised these boards because they fulfill the basic functions of a breadboard. Nothing extraordinary here--it's just a breadboard--but these breadboards are not broken on arrival. Is this indicative of an impending fall of our civilization? Where we praise the fact that a product meets the basic criteria of its function? Where not being broken is spectacular? I'd argue, yes. We're done for. Too bad there are no other companies making breadboards of the quality these have, but at half the price (how about you BusBoard?) They are just breadboards after all. Shouldn't be the most expensive part of a project. But since all the competitors absolutely suck, or are just as expensive, this is the only product we can get that isn't broken. Thanks "free market." I would have twice as many of these if they were half the price. Lastly, They install so easily on the sticky backing they come installed on. Check. Gimme a green check mark and word. Feels very annoying to not see all the points at the bottom of this review field/box checked and green, and feels like nothing at all knowing that I have met all the criteria for leaving an informative or helpful review--alot like buying breadboards in 2025. Once the power goes out, no trace of these words will remain. But seriously, I do appreciate that you guys sell a product that isn't broken. Its non-broken-ness is what makes it good.

Works perfectly

I have used a series of cheap, generic, breadboards. I was always troubleshooting the breadboard connections more than I was troubleshooting the circuit. I started to just solder all my circuits together because at least then I knew the electrical connections would be good. I watched a YouTube review that concluded that this was one of the good breadboards, so I bought a couple. The first circuit that I made was an amplitude modulator at 45 MHz. Just a single FET, some biasing resistors and decoupling capacitors. The circuit worked the first time I powered it! I never would have used one of the cheap breadboards for this since it's RF. The resistors even have thin 0.3mm leads that were problematic on the other breadboards. They cost more, but I think they are worth it.

I've been using breadboards a long time. My first breadboards were the dual-rail, all-white x-y types, so I really dig the quad-rail red-blue things that are popular these days. I have a bunch of breadboards currently, and they all have projects on them, so I needed to get some more. I originally found this board on amazon, and added it to my cart. Then I found the Elenco 9830C for 5 cents cheaper (although, at time of writing this the Elenco boards are 7.11 instead of 7.95). So I ordered 2 Elenco boards and one BB830. I got the Elenco boards a day earlier, and was immediately disappointed to find that the backing was 1) mostly non-adhered (though fixable with some thumb-action) and b) didn't have a double-sided backing. Not a big deal, really, but perhaps notable. A day later (today) I got the BB830. I have them side-by-side right now, and the quality difference is actually significant. 1) The Elenco board is warped where the BB830 is straight. The rails on the Elenco board curve inwards rather flimsily, whereas the BB830 is flat and solid. 2) The print quality of the numbers and letters on the Elenco board is dark, blotchy and still somehow washed out, with whole character segments missing or run together. The same printing on the BB830 is really crisp and clear. It's like a typewriter versus a laser printer. 3) This is not really a quality difference but more of a preference: on the Elenco boards, the letters are lowercase, while on the BB830, they are uppercase. Oddly, I think I prefer the uppercase, although it may be the obvious difference in print quality that is swaying me. 4) The BB830 comes with a padded, double-sided backing. This isn't really a huge deal on its own, but most of the breadboards I already own have this same feature, and it feels better somehow. If the Elenco boards had even the thin adhesive backing fully in place and sealed, I probably wouldn't even bring it up. 5) This should have probably been number one. There is a VERY noticeable difference when plugging in leads (using "premium" jumpers to test, I think 22 gauge). The BB830 has a light-but-firm feeling on entry and then a clean, secure tug. Very smooth. The Elenco boards are tougher to insert leads into and have an almost "rusty", grating feeling when inserting the lead. I've never paid specific attention to these things before, but it makes a huge difference. All told, they both do the job that needs doing, but I already know the BusBoard (distributor? mfgr?) breadboards will last longer and be more pleasant to use. Nitpicks: Elenco has better packaging, although I recommend that it not be a selling point. Elenco also spells breadboard as "bredboard." Um, whatever.

Das Board wirkt etwas klein (wenn man vorher nur an Lochplatinen rumgespielt hat) hat aber genügend Platz für alle alltäglichen Spielereien. Kontakte fassen ordentlich auch bei dünnen Drähten. Klebestreifen hinten. Wirkt schon durch das Gewicht wertig. Aufdruck deutlich und sauber und lässt sich nicht abkratzen. Kann man bei den Dingern was falsch machen? Recht simples Teil das es schon ab 2,99, mit etwas suchen, gibt. Habe 8.50 mit Prime bezahlt - geht.

Works good for price

This breadboard is pretty amazing. It does almost everything that a breadboard it's suppose to do. Pros: + easy to insert just about anything into it without bending the pins + no loose contacts. Just enough pressure to ensure a good contact + comes with a back plate. + everything is labelled properly Cons: - you can only attach more breadboards on only 2 of 4 sides of it. Do yourself a favor and give these breadboards a chance. And you'll never look back at those other cheap breadboards.

strumento perfetto, funzionante e performante, risponde a quello che mi aspettavo di trovare comodo, poco ingombrante, e ben fatto.. utilissimo

Items all came boxed, no manufacturers details. Quality for these boards is very good. All printing is clear. Contacts within the board have flared openings to allow easy wire/component insertion and grip firmly. Based onthe quality of these I placed a 2nd order.