Generic Torque Converter Motor Riser Mount Plate 1-3/4" Lift

Very sturdy, great price, was easy to install. Functions as it should and looks great

Exactly what you need at a very fair price. Fits just right. Everything about it is as advertised. I have one in my BT200X to accommodate my torque convertor

So, I'm doing a cart build and, I have already spent 75$ on a riser plate from someone else and, it broke at the welds. I payed way less here and, I received a product I'm gonna rate at a high 6 stars. I love it, it has absolutely made things a whole lot easier for me and, it's built strong and not bulky at all!!! Absolutely recommend this product!

I bought a few of these recently and compared to another seller this one has a nice textured paint job and came with correct size hardware to mount a predator 212. I drilled out the rivets and used my own grade 8 hardware though. If you look at the bottom you can see where the top plate passes through slots on the bottom plate and is welded there at those slots. Seems like a strong design compared to the other one I bought. This one does only have a seam weld on top as opposed to some actual weld beads. But I think the pass through welds on the bottom make up for it. It’s no OMB plate but it’s also half the cost and works fine.

Fits good fast shipping would order again

Great riser plate for your mini bike engine! Great value for the money and build high quality. Installation was easy and it gave me the option to raise my motor for the right position fro chain and sprocket.

Nice item. Threads seems a little rough but will work. Shipping was slow.

I have a predator 212, motor lines up well but the top bolts that hold the motor to the motor mount are way too short, needs at least a half an inch longer bolt to safely secure the motor. The bolts won't even thread.

Fit great on my BT200x to be able to mount my torque converter. Great hardware that came with it aswell. I had to come get another for my second bike.

If you are considering doing an upgrade to a torque converter on your Coleman mini bike, this is must. It is a quick, easy way to set the engine up and forward. I have seen some Mickey Mouse jobs with built up spacers, square tubing, etc., but for the money this makes the whole thing a lot easier.

I have actually ordered 2 of these for the price they are great just expect the theads to be damaged on arrival.

So after ordering 3 of these engine riser mounts over the last number of months,I finally received one that was aligned and welded straight for a change.Two others that were bought previously were the versions that had the 3 holes on each side of the mount and the 2 plates were welded out of square with each other.The latest engine riser is the version that has the 3 slots on each side as opposed to holes.It lines up perfectly in squareness because the upper and lower plates are cut with tab and slot alignment guaranteeing perfect alignment in welding every time.The version with the round holes in the sides uses zero alignment aids and leaves it up to the welder to use the T.L.A.R method(that looks about right).One mount was off by around 1/8" in squareness to the bottom plate and the second one was just slightly more than that.The first 2 mounts I received with the round holes on the sides were MIG welded and had 2 welds (top and bottom) ground down to the point of gouging/dishing the weld area slightly.This last mount with the 6 slots on the sides is way better aesthetically speaking.The welds are super fine and clean and I suspect the welds are laser welds to be this small of a weld bead(not TIG).It is also a continuous weld that runs the entire length of the plate.The original 2 crooked plates had 3 small welds on each side and were acceptable but the laser weld is much less noticeable and cleaner looking.Even the alignment slots and tabs were laser welded from the looks of things and very well done.The negative points for this rating come from the decision to ship a 4lb piece of steel just wrapped in cling wrap then thrown into a unpadded brown paper shipping bag.When it arrived here,one corner of the steel mount had torn right through the side of the paper envelope.Big surprise.Upon closer inspection of the mount,I noticed damage to the paint and steel from being dropped onto a very hard surface(likely concrete floor) because the edge of the steel was actually mushroomed from the impact.This was shipped from the U.S to Canada like this.Absolutely zero impact protection.How hard would it have been to put it in some bubble wrap and throw a 4lb piece of steel in a proper cardboard shipping box.Total incompetence I M.O.Thus the 3 star review.