K2020A+

Update - the amp performance still bothered me, too many positive reviews here so I did more testing. I tried yet another set of speakers, some Paradigm Atoms that seemed to be sized well for the T2020. I also dragged out my AudioSource Model 2 so I could baseline the Atoms. Turns out the Atoms sound fine with the Kinter. So why didn't the Klipsch sound fine? I expect the two 6" woofers were just a bit much for the Kinter and the 12V factory supply and that's why the bass suffered. Also the tweeter in the Klipsch is way louder than the Atoms - I didn't not hear the switching noise as loudly with the Atoms but clearly heard it with the Klipsch. How does the T2020 compare with the AudioSource on the Atoms? It's probably 90% as good according to my tin ears. Bass was fine, treble was fine, nothing fuzzy or distorted sounding; totally acceptable for the price of the T2020. What about the switching noise? Well turns out I was probably hearing some inter-mods aliasing down in the audio range. With the volume all the way down and the audio input cable disconnected from the source you can see an 870KHz oscillation on the speaker outputs from the class D driver. I tried to get a scope shot of the aliased lower frequency noise but the best I could do was a 32KHz-ish scope shot. My hearing rolls off sharply above 13KHz but you can definitely hear idle "hiss" if your tweeters are any good. Is it a problem? Well I will leave that up to you to decide, as a studio monitor this is probably not your amp but to fill a room with sound, you will probably never hear the hiss. How well did it do with bass and high frequency? Well I did some scope shots to get you some data. These were taken in parallel with the speaker acting as a load and you can see the switching hash at high frequencies to be sure but you can't really perceive it. The 40Hz looks fine on the scope and the 20KHz looks a little hashy but hey - that's how class D works, not much you can do about it. I included some shots of the AudioSource so you can see the difference. The sine wave was from a function generator app on an iPhone for both amps. The AudioSource has the higher p-p voltages and the cleaner output obviously. What about the minimus 7s? Well they stink compared to the Paradigms of course but that's kinda apples and oranges. When I put the minimus 7s on the AudioSource they sounded similar to the Kinter so I began to suspect there was a speaker problem. The woofer surround looked fine when it was mounted in the speaker but when I removed the drivers I could see a crack at the base of the foam, which is why the bass suffered so badly in these units. So I put in some generic 4" woofers and the minimus 7s sound ok now on both the AudioSource and the Kinter. To be honest the Kinter sounded slightly better as you could boost the bass with the tone controls to match the tiny speakers. Bottom line - buy this amp if you have reasonable expectations and reasonable speakers, it sounds fine and it is worth the money. If you are pushing too big a driver you might be sad, but for a modest system the T2020 does just fine. Oh and this is not a paid review, I bought this thing. Also bought a DAMGOO bluetooth amp with the TPA3116D2 part in it. That amp sounds fine as well given the cost, same comment on the hiss, but no scope shots of it yet. ================= original review below =================== Wanted to like this amp based on the many reviews but they didn't deliver at all on sound quality. Initially I hooked it up to a pair of Minimus-7s figuring they should be well matched and used my iPod as the source. Started with the tone knobs both on mid range. The high end was super bright and clear but bass was muted. Fine, cut back on the treble knob and cranked up the bass and the amp delivered a fuzzy and muted thump for every bass drum kick. Ok - maybe the surrounds on these speakers are bad? Nope - the drivers had been replaced and the foam was all good. Ok maybe the crossover is bad, I'll try a different speaker. So I hooked up a known good Klipsch RC3 center channel speaker which has 6" woofers in it. Cranked the bass up again and it started to come through but still felt very thin. For something like a cello or standup bass notes you can probably get away with it, but for any music with a backbeat and some punch this amp falls flat on its face. Also there is a continuous 13KHz hiss coming out of the speakers, either with or without an audio source - regardless of volume level. Very noticeable, not acceptable. The final straw was when I plugged the iPod back into the Cambridge Soundworks model 88 radio I was trying to replace. Night and day difference, the model 88 has tons of bass punch compared to this amp, and my model 88 has had a long and hard life in the shop and has been rode hard and put away wet. It has a tiny 4" driver and it put our more bass than the alleged 20W into the RC3. If you own Klipsch speakers you know how loud they get and how efficient they are, it's kinda their "thing". If this amp can't drive a Klipsch, what the heck can it drive? Maybe I got a dud, or maybe all the hype was too good to be true, don't really care. Don't buy this amp unless you long for the sounds of a paper dash speaker with a whizzer cone in your clapped out Chevy II, and a photo flash unit charging up next to your head.

When I spotted this little amplifier on amazon the other night (3/8/2018) there were 16 left. When I thought to myself the following night that perhaps having a second one might be fun for a blu tooth set up meant for listening while in the shower? They were completely gone already. I expected them to go fast, but damn! Ok, so I bought this to use for testing mostly. I have three pairs of Dayton Audio B652-Airs that I purchased a while back to use for the '5' in our 5.1 surround sound set up in our theater room. The B652-Airs get great reviews, sound especially good for their price, and are ones that have a good following among those who like to modify inexpensive speakers in order to get better performance from them. I wanted to do the same, so I needed an amp. This one has the infamous/extinct Tripath TA2020-020 amplifier chip, came in at a good price, and already had a few positive reviews... so home to me it came. Initial impression: It was packaged well with no excessive stuff inside. In the regular brown cardboard box with the company logo and slogan/motto on it? was a double-sided one page operating manual, a power supply with its wall plug, the amplifier, and some squishy foam to keep everything safe. No excess, but probably more than what I was expecting for the 30 bucks I paid including shipping. The amp: Its a nice, simple amp. Everything is clearly labeled and everything is sturdily mounted. Nothing on it wiggles or is loose. It is certainly well built from what can be learned from the outside. All the knobs are easy to turn AND get to, something that is not always easy to accomplish for a guy with large hands. The performance: Obviously an amplifier's performance is best measured with scientific equipment, none of which I have. An initial 30 minutes of listening had my ears telling me the audio sounded pleasant on pleasant sounding speakers, nothing sounded muted or stuffy or electric (think about cheap pocket radios and the audio that comes out of them to understand my use of the term "electric"). I found myself wanted to find time to keep listening and skip doing other things I needed to do because I was enjoying just listening to music. One thing I always check for is excessive 'hiss' when a speaker is hooked up to an amp that isn't playing anything or connected to an audio source. While there certainly is some with this amp as with most, it is nothing that is noticeable from more than a foot away or less with the amp turned to full volume. If you made it this far down? I realize I'm leaving a review on a limited edition amp that has already sold out and may never return. But if you are reading this and it becomes available again? And you're on the fence about making the purchase? Don't be. Just buy it. Its more than worth the 30 bucks, and you'll be happy that you did. 5 stars hands down. Also, I like to see photos in the reviews I read, so I've included a bunch for anyone who may be interested. I didn't take the time to measure the dimensions of the amp, but I've included a Pepsi can for size reference. Thanks for reading, hopefully this was helpful to someone out there.

Excelente equipo de audio! Los componentes internos Texas Instruments son digitales producion un audio HI FI único para audiofilos!

The sound is pretty amazing. The interface is simple, easy to setup, and operate. The unit is very light, so it's best if it can be mounted somewhere, otherwise every time you try to push a button or rotate a dial, it moves. The markup was a bit steep though (reason for docking a star), still a great purchase.

I bought this amp to replace an older Lepai that had given up the ghost, since the current Lepai or Lepy models don't use a tripath anymore and as a clone of those amps it fits the mounting holes I already had on my desk. It made my speakers buzz and whine softly from the moment I plugged it in, even without a source connected. Unfortunately I procrastinated a few months before setting it up and was well past the return period so I had to live with it. Tonight I woke up to the kind of popping and crackling noises that sounded like a bonfire and panicked thinking my apartment was about to burn down. Turns out there was no fire, I had just forgotten to turn this piece of junk off before going to bed and it was feeding loud static through my speakers. Since I won't be falling back asleep any time soon after that adrenaline surge, I'm instead writing this to warn other buyers: spend your money on something else.

Was working fine and now no sound. Switch with another amp and sound works fine. Kinter has not responded to request for replacement? Buyer Beware!!!!